Installation Manual For ISM/ISM02/ISM07 M11/M11 Plus Engines
10 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESSection 4: Electrical InstallationM11 CELECT™ Wiring Installation
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 11M11 Plus CELECT™ Plus Wiring Installation(Model 411)FIG. 21ISM Wi
12 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESISM02 Wiring Installation(Models 411D)For proper electrical wirin
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 13The CBrake by Jacobs™ Model 411, 411C, 411D, & 411E installat
14 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESReplace Rocker Lever Cover1. Remove the gasket and inspect for d
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 15Section 6: Brake MaintenanceTheory of OperationEnergizing the eng
16 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESThe CBrake by Jacobs™ is a relatively trouble-free device. Howeve
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 172. Slowly remove cover until spring pressure ceases, then remo
18 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESSolenoid Valve1. Disconnect the solenoid harness. Using a 3/4” s
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 19Slave Piston Adjusting Screws (Reset)1. Loosen slave piston adju
2 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESTable of ContentsSection 1: Introduction ...
20 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESMaster Piston1. Remove the button-head screw, washer and master
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 212. While holding the tool in position, screw the holder down ove
Cummins Inc.Box 3005Columbus, IN 47202-3005U.S.A.www.cummins.comCELECT™ is a trademark of Cummins Inc.Bulletin 3698827For additional support, visit w
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 3 Section 1: IntroductionModel 411/411C/D/EAftermarke
4 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESSection 2: Engine PreparationClean engine thoroughly. Remove engin
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 5 4. Lubricate the actuator pins and valve stems with clean lube o
6 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES3. Place a 0.027” (0.68 mm) feeler gage between the rocker lever
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 7Housing Installation NOTE: ALSO REFERENCE CUMMINS TROUBLES
8 CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINESSlave Piston AdjustmentPAY SPECIAL ATTENTION TO THIS ADJUST-MENT.
CBRAKE BY JACOBS™ INSTALLATION MANUAL FOR CUMMINS ISM/ISM02, M11/M11 PLUS ENGINES 9Installation of Oil SupplyDO NOT CONNECT THE ENGINE BRAKE OIL SUPP
Comentarios a estos manuales